Chatillon Ametek |
|
Chatillon Ametek Bollard Grips
FREE Ground Shipping *
From: $3,365.70
A range of pneumatic grips with either single or double actuator, single actuator grips have one side adjusted by manual tightening action either by thumb screw or T-bar, these grips are suitable for offset sample alignment for shear testing Ideal for all types of flat samples, rubber, plastic film, plastic dumbbells, paper and cardboard, sheet metal, foils, wood, fabrics and composites (depends on rating)
All pneumatic grips are suitable for use with the foot and hand controls more ...
|
|
|
|
Chatillon GF-8 Adhesive Test Block
FREE Ground Shipping *
$473.10
This fixture has detachable, circular face plates made of hardened steel. A ball socket mounting screw helps keep upper and lower plates parallel and perpendicular to the applied force. 500 lb capacity.> more ... |
|
|
Chatillon GF-54 Three Point Bend Fixture
FREE Ground Shipping *
$553.80
The Model GF-54 grips come in pairs and are designed for compressive three-point bend applications. Grips support unidirectional bending on rigid and semi-rigid materials. Grips mount using #10-32 thread mounting holes (provided)> more ... |
|
|
Imada |
|
|
|
|
|
|
|
|
|
|
|
|
Mark 10 |
|
Mark 10 M5-2-COF Coefficient Of Friction Gauge
FREE Ground Shipping *
From: $2,755.00
The G1086 COF fixture is an integral part of a COF measurement system, typically including a motorized test stand and COF gauge. The G1086 can be used for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients can be measured using the included M5-2-COF gauge more ...
|
|
|
|
Mark-10 G1071 TAPPI T829 Score Bend Fixture
FREE Ground Shipping *
$503.50
This set of fixtures is used to produce a 90° bend in fiber board materials and plastics. The fixtures are compliant to TAPPI standard T829 for evaluating the relative quality of scores in corrugated containers.> more ... |
|
|
Mark 10 G1104 Flip Cap Pull Grip #10-32F
FREE Ground Shipping *
$171.00
Designed to engage the tab on a flip cap for pull-off force measurements. A spring-loaded hook retracts as it is lowered into the starting position, then snaps into place below the tab> more ... |
|
|
|
|
|
|
|
Mark-10 G1072 Opening Force Fixture Set
FREE Ground Shipping *
$456.00
Used to determine the opening force of flat folded cartons along their score lines. Ideal for numerous applications in the packaging, food and beverage, medical device, consumer products, and many other industries.> more ... |
|
|
|
Mark-10 G1098 ASTM D6195 Loop Tack Fixture
FREE Ground Shipping *
$931.00
Designed for tack force testing of pressure-sensitive adhesives, in conformance with ASTM D6195 and related standards. A looped sample is loaded onto the test strip, and the closed end of the loop is secured by an upper grip (not included - suggested model: G1008). The test strip may be indexed in three positions, allowing for three tests to be performed between cleaning cycles. The strip is secured and released by a lever-operated clamp. An additional set of three test strips is available.> more ... |
|
|
|
Mark-10 G1086 ASTM D1894 Coefficient of Friction Fixture
FREE Ground Shipping *
$1,695.75
The G1086 COF fixture is an integral part of a COF measurement system, typically including a motorized test stand and COF gauge. The G1086 can be used for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients can be measured using the M5-2-COF gauge.> more ... |
|
|
Shimpo |
|
Shimpo Steel Adapters For use with 500 - 1000 lb force gauges
FREE Ground Shipping *
From: $562.50
O’s Adhesive Test Plate attachments with hardened tool steel, detachable face-plates can test samples up to 3” (76.20 mm) in diameter. Ball socket mounting screws in both grips assure parallelism and perpendicularity to force when load is applied. Grips and attachments sold individually (not in pairs). more ...
|
|
|
|
|
|